* Add revision 1 and revision 2 to ProjectKB Alice PCB
* Swap SLEEP LED to no
* Basic root rules.mk
* Apply suggestions from code review
* Update keyboards/projectkb/alice/rules.mk
Using just qmk setup <github_username> would fail w/ "Could not find repo github.com/<username>, whereas the repo is actually after another slash after the user name. Can consider changing code to add the default forked repo name if slash is not detected in the arg.
* add VIA enabled keymap with some layers taken out for space
* get a more sane VID and PID so we don't collide with the other BMC powered boards
* small cleanups
* Update keyboards/tgr/jane/keymaps/via/keymap.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* add tkl_ansi_tsangan LAYOUT
* add tkl_iso_tsangan LAYOUT
Co-authored-by: Ryan <fauxpark@gmail.com>
* porting the niu_mini to via
* Wrong values in mk
* Updating to unique Vendor ID and Product ID
* Addressing zvecr comments
* Addressing fauxpark comments
Co-Authored-By: Ryan <fauxpark@gmail.com>
Co-authored-by: Lauren Harris <lauren.y.harris@outlook.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add support for hardware and board initialisation overrides.
* qmk cformat.
* Add some documentation.
* Docs clarity.
* Make early_hardware_init_pre a no-op for now, until migrations occur.
* Doco update
* Make distinction between keyboard and ChibiOS board in docs
* Doc anchors.
* Update tmk_core/protocol/chibios/main.c
Co-Authored-By: Joel Challis <git@zvecr.com>
* Rework bootloader entry to be off by default, allow opting-in.
Co-authored-by: Joel Challis <git@zvecr.com>
* id80: New keyboard (IDOBAO ID80)
Add initial support for the IDOBAO ID80 keyboard.
Most source files were generated by the KBFirmware JSON to QMK Parser
(https://noroadsleft.github.io/kbf_qmk_converter/) based on the
ID80.json file provided by the keyboard vendor. The only change to
rules.mk was to set `COMMAND_ENABLE = no` to make the compiled firmware
fit into the available flash space.
* id80: Update default keymap to match stock
Update the Fn layer in the default keymap to match the stock firmware
which was actually flashed into the PCB.
* id80: Add Caps Lock indicator support
Although the KBFirmware JSON includes information about the MCU pins
used for keyboard indicator LEDs, the KBF to QMK converter does not
generate the required code automatically. Implement the LED handling
code, and at the same time switch from the older `led_set_kb` API to the
newer `led_update_kb`.
* id80: Remove placeholder functions
The provided skeletons for `matrix_scan_kb` and `process_record_kb` did
not do anything useful, so remove them.
* id80: Use Esc as the Bootmagic Lite activation key
The Esc key is not at the (0, 0) position in the ID80 matrix, therefore
setting `BOOTMAGIC_LITE_ROW` and `BOOTMAGIC_LITE_COLUMN` is required to
use the Esc key for Bootmagic Lite.
* id80: Update info.json
Replace info.json generated by the KBF to QMK converter with another
version generated using http://www.keyboard-layout-editor.com/ and the
KLE raw to QMK info.json converter (https://qmk.fm/converter/). The
updated info.json has the correct physical layout (the distance between
the function key row and the main block is actually 0.25U, but the
vendor-provided ID80.json had 0.5U there) and correct key labels (using
the stock layout instead of raw matrix locations and pin names).
* id80: Enable NKRO
The default keymap is updated to have NK_TOGG at Fn+N, like most other
keyboards which have NKRO enabled.
* id80: Use unique USB vendor/product ID
Having an unique USB vendor/product ID is required for VIA support.
The vendor ID value is the same as for the `idobo` (ID75) keyboard.
* id80: Fix right modifiers in the default keymap
For some reason the default keymap converted from the vendor-supplied
JSON had the right Shift, Alt and Ctrl keys mapped to the left side
modifier keycodes.
* id80: Remove empty row 6 (F0) from matrix
The matrix layout which was defined in the vendor-supplied ID80.json
file had 12 rows which corresponded to the left and right parts of the
6 physical rows. However, the row 6 of the matrix (connected to the F0
pin), which corresponded to the right part of the physical bottom row,
was completely empty (all 9 keys of the bottom row were placed in the
matrix row for the left part). Keeping this row in the matrix just
wastes resources; in particular, when the VIA support is enabled, having
a 9×12 matrix with 4 layers leaves only 122 bytes available for dynamic
macros, which is less than the recommended minimum of 128 bytes.
Removing the unused row reduces the matrix size to 9×11, which leaves
194 bytes of EEPROM space for dynamic macros.
* id80: Update row numbers in the LAYOUT macro
Update row numbers in the names of the LAYOUT macro parameters after
removing a row in the middle.
* id80: Set RGBLED_NUM to 20 to match the actual PCB
The vendor-supplied ID80.json file specified that the PCB should have
28 RGB LEDs in the chain. However, the actual PCB that was shipped
from AliExpress had 20 LEDs in the chain (16 underglow LEDs, and then 4
more LEDs on top of the PCB, to the right of the Enter key location).
Update RGBLED_NUM to match the actual PCB.
* Add support for Caps Lock LED
Currently ignores the fact that led_state is not synced between halves, so caps lock LED doesn't do anything if USB is plugged into right half
* Set initial backlight and RGB mode/values on blank EEPROM
* Set default VIA layout options
* Add backlight/RGB ifdefs
* Set bootloaders for each rev
* dipsw test on helix/rev2/sc/back:five_rows
* bug fix quantum/dip_switch.c
* test end. remove test code. Revert "dipsw test on helix/rev2/sc/back:five_rows"
This reverts commit 4b13ebb996e1c4997e6deb1fa3b3227db5fa9661.
* dipsw test on helix/rev2/sc/back:five_rows
* update quantum/dip_switch.c
* test end. remove test code. Revert "dipsw test on helix/rev2/sc/back:five_rows"
This reverts commit bf99ace095528ad65c531229bcf5ece037dda595.
* Add handwired BDN9-BLE
* Apply suggestions from code review
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update keyboards/handwired/bdn9_ble/rules.mk
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update keyboards/handwired/bdn9_ble/rules.mk
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update keyboards/handwired/bdn9_ble/readme.md
Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
GCC 4.9.4 is no longer available on Gentoo (or Sabayon), which causes
problems when attempting to install on either of these platforms. Since
QMK is not particularly sensitive to its GCC version, modify the version
restriction to <9 so newer versions of GCC may be installed. Since the
toolchain for arm-none-eabi isn't currently installed as part of setup,
add that as well.
Additionally, drop the Python installation as part of the Gentoo
installation process. Python is a core system package on Gentoo and can
therefore be assumed to be present; in addition, the slot restriction of
3.5 which was present is also no longer available in Gentoo.
Finally, separate the gcc rebuild invocation of `emerge` from the new
packages that may need to be installed, and apply the `--noreplace` flag
to new packages so that they are not rebuilt if already present.
Mikkel Jeppesen
stanrc85
umi
Ryan
Andrew Kannan
skullydazed
James Young
MakotoKurauchi
Daniel Klein
Andrew Kannan
Jason Scatena
x1
Pete Johanson
Øyvind Wilhelmsen
mimkorn
eucalyn
Aplyard
Pavlos Vinieratos
Casey Leask
Nick Brassel
MechMerlin
Gautham Yerroju
Joshua Rubin
codecoffeecode
Sergey Vlasov
Danny
Derek
Takeshi ISHII
Konstantin Đorđević
George Petri
QMK Bot
artjomsR
jotix
Benjamin Smith
Drashna Jaelre
Joshua Moses Diamond
James Forcier